Williams Sound WIR TX8 Guide d'installation

SoundPlus™WIR TX8 Infrared Emitter,95 kHz and 250 kHz CarrierLarge Area Infrared Listening SystemModel WIR TX8Optional Receiver Model WIR RX4Installat

10POWER WIRINGFOR U.S. APPLICATIONS:The TX8 Emitter is supplied with a low-voltage wall transformer power supply (TFP 010). Two-conductor 18 ga. power

11IF YOU ARE USING MORE THAN ONE EMITTER:Step 1: Determine the length of coaxial cable needed to reach between the emitters. 100 feet (30 m)of coaxia

12Nut Secured IntoPlug Assembly50 Ω BNC Plug ConnectorPlug AssemblyContactClampGrooved SideGasketWasherNutGasket (note groove)WasherNutCable Jacket7.9

13CONTROLS AND FEATURESPOWER INPUTThree-pin connector for TFP 010 power supply.POWER INDICATOR LED (FRONT PANEL)Located on the front panel in the top

14CAUTION!CAUTION!CAUTION!RECEIVER SAFETY INFORMATIONHEARING SAFETYThis product is designed to amplify sounds to a high volume level which couldpotent

15OPTIONAL RECEIVER INSTRUCTIONSIR RECEIVER MODELS WIR RX41. Turn the receiver’s Power Switch to ON. 2. Place the headset on your head and find the

16TROUBLESHOOTINGNEITHER TX8 INDICATOR LIGHT IS ON (FIGURES 1B, 10 & 11). Make sure the wall transformer is plugged into the emitter and the powe

17SYSTEM SPECIFICATIONSINFRARED EMITTER, MODEL WIR TX8Dimensions, Weight: 11.25" W x 6.25" H x 2.125" D (28.6 cm x 15.9 cm x 5.4 cm)

18INFRARED RECEIVER, MODEL WIR RX4 (OPTIONAL)Weight: 5.4 oz (154 g) with batteriesEarpad Size: 6.5 cm (2.5") diameter, adjustable headband, uses

19LIMITED WARRANTYWilliams Sound products are engineered, designed, and manufactured under carefully controlled conditionsto provide you with many yea

2SOUNDPLUS™WIR TX8 INFRARED EMITTER, 95 KHZ AND 250 KHZ CARRIERINSTALLATION GUIDE AND USER MANUALContents PageSYSTEM OVERVIEW 3INSTALLATION PROCEDURE

®10321 West 70th St., Eden Prairie, MN 55344 U.S.A. 800.843.3544 | 952.943.2252 | FAX: 952.943.2174www.williamssound.com© 2006, Williams Sound Corp.

3SYSTEM OVERVIEWThe Williams Sound WIR TX8 Infrared Emitter is designed to operate with a WIR TX10Infrared System or modulator that sends a 95 kHz or

4TX8 Emitter95 kHz/250 kHz ModulatorPower Supply120 VAC (US): TFP 016230 VAC (CE): TFP 027Baseband InBaseband OutPower Supply120 VAC (US): TFP 0102

5TX8 EMITTER COVERAGE PATTERNS0 10 20 30 40 50 60 70 80 90 100 110 120 130 1400 3 6 9 12 15 18 21 24 27 30 34 37 40 439080706050403020100- 10- 20- 30-

6FIG 3a: 3-Dimension Foot PatternThe TX8 floods the listening audience with a cone shape light pattern as shown here. The path of the cone shape lig

7Reflections of the infrared light from walls, ceilings, and floors may change these patterns. Important: Remember to point the emitter towards the l

8TX10Coverage area with Single EmitterCoverage area with Second Emitter Added to Same Emission Point (50% increase)TX8Multiple Emitters Installed to M

9FIG. 7: WALL OR CEILING MOUNTFigure 7a: Mounting the TX8 onto a wall with the BKT 024. Tip:To keep the TX8 level,rotate the tension screw (Fig. 6)so